Mauser gewehr 98 scope original
![mauser gewehr 98 scope original mauser gewehr 98 scope original](https://images.gunsinternational.com/listings_sub/acc_6533/gi_101478414/WW1-IMPERIAL-GERMAN-MAUSER-GEWEHR-98-GEW98-SNIPER-RIFLE-WITH-SCOPE-AND-CLAW-MOUNTS_101478414_6533_A4AC9C34ECA88F05.jpg)
![mauser gewehr 98 scope original mauser gewehr 98 scope original](https://s3.amazonaws.com/mgm-content/sites/armslist/uploads/posts/2017/12/28/7756962_04_mauser_gew_98__640.jpg)
Patrone became the standard German service ball cartridge in the 1930s. Because of this the S Patrone was phased out in 1933 and the s.S. Patrone, originally designed for long range machine gun use, produced less muzzle flash out of rifles that had a shorter barrel and also provided better accuracy.
![mauser gewehr 98 scope original mauser gewehr 98 scope original](https://www.empirearms.com/8459gg.jpg)
The 1903 pattern 7.92×57mm Mauser S Patrone produced excessive muzzle flash when fired from arms that did not have a long barrel like the Gewehr 98. The desire for adopting new shorter barreled rifles and the introduction of the Karabiner 98k, featuring a 600 mm (23.62 in) long barrel, were reasons for changing the standard German service ball rifle cartridge. Just like its predecessor, the rifle was noted for its reliability, great accuracy and an effective range of up to 500 metres (550 yd) with iron sights and 1,000 metres (1,090 yd) with an 8× telescopic sight. Since the Karabiner 98k rifle was shorter than the earlier Karabiner 98b (the 98b was a carbine in name only, a version of Gewehr 98 long rifle with upgraded sights), it was given the designation Karabiner 98 kurz, meaning "Carbine 98 Short". The Karabiner 98k was derived from earlier rifles, namely the Mauser Standardmodell of 1924 and the Karabiner 98b, which in turn had both been developed from the Gewehr 98. In February 1934 the Heereswaffenamt (Army Weapons Agency) ordered the adoption of a new military rifle. The Karabiner 98k therefore continues to appear in conflicts across the world as they are taken out of storage during times of strife. Millions were captured by the Soviets at the conclusion of World War II and were widely distributed as military aid. rifle with original German military - type scope mounted on the left side or. Although supplemented by semi- and fully automatic rifles during World War II, it remained the primary German service rifle until the end of the war in 1945. German Gewehr 98 rifles, in caliber 7.92mm, bearing chamber dates of 1899. It was one of the final developments in the long line of Mauser military rifles. Good luck with your project.The Karabiner 98 kurz (German: "carbine 98 short", often abbreviated Kar98k or K98k and often incorrectly referred to as a "K98" (which was a Polish Carbine), is a bolt-action rifle chambered for the 7.92×57mm Mauser cartridge that was adopted on 21 June 1935 as the standard service rifle by the German Wehrmacht. Mauser Model 98 with Voigtlander Braunschwelg Claw Scope and Lymon Adjustable Open Sight (B8460-18). I do have a B-Square model mounted on a WW II vintage Mauser, but can't readily access it for measurements, and they might be somewhat different as the WW I Mauser had the Lange "roller coaster" rear sight. Can you make it? Sure, if you have the skills and tools and if machine work is part of your hobby then go for it. As far as making your own, they are relatively inexpensive and I'd recommend buying one. Brownell's usually carries them in stock, but you can order direct from most manufacturers. Good places to start looking are B-Square and ATI, and there are other mount makers as well. You will need to purchase a scout-type scope with long eye relief. They are quite simple to install, and if maintaining your historic rifle in original condition is your goal, then they are a good way to go, as you can re-install your original sight parts should you desire to remove the scope. There are several brands, and all utilize the holes in the ears for attachment and usually a third screw. You have to remove the elevation slide bar and its spring, and then the mount fits between the original sights base or "ears". It doesn't actually fit over the rear sight. Stick around-you'll like it here!Īfter thinking about your request for awhile, I believe what you're after is a scout scope-type mount.